Why the magnetic clutch does not normally operate

1. It is best to choose a quality-assured secret machine magnetic powder clutch product.

2. When choosing to purchase a magnetic clutch/magnetic brake. Filled with granular magnetic powder (approximately 40 micrometers) When the magnetic coil is non-conductive, the magnetic particle clutch is a combination of the transmission unit (input shaft) and the output unit (output shaft). The space between the two sets of units. The torque is not transmitted from the propeller shaft to the driven shaft. However, if the coil is electromagnetically energized, the magnetic powder is attracted by the magnetic force to cause hardening, and the torque is transmitted between consecutive slips. The principle of the magnetic powder brake is similar to the magnetic powder clutch, except that the transmission unit is changed into a fixed unit.

Magnetic clutch/brake jams usually occur in the following situations:

In the absence of excitation before starting up, it will be stuck. 1. The magnetic powder filling between the two groups of units is scattered due to the long time during transportation or for a long time.

The magnetic powder brake rotor concentricity is not enough, 2. The product manufacturing accuracy is low. Causes uneven output torque or stuck.

3. Enclosure of excessive magnetic powder in the production process.

4. Caused by using inferior magnetic powder.

Recommendation: For the above situations.

Must be run evenly to formally operate. Magnetic clutch can produce smooth torque in this way, 1. Before the formal operation or after the device moves. The uniform operation mode is as follows: in the non-excited state, the drive side is rotated as fast as possible (below 1800 rpm) for about one minute, and then the excitation current is set at the rated 1/4 to 1/5 on one side of the rotary drive side, on the other hand, for 5 seconds. On, off in 10 seconds, between 20 and 20 times.

Article Source: Magnetic clutch brake http://

Dabcool Vaporizers

Features:

1. On/Off:Press For 3seconds

2. 4 Unique Manual Heat Settings(450ºF/500ºF/550ºF/600ºF)

3. 20 Second Average Heat-Up Time

4.Micro-USB Fast Charging, Full Charge Time:About 2 Hours

5.Atomizer For Puff peak

6.The Device Has Low Voltage Protection, Short Circuit Protection And Overheating

Protection.

7.1500mah built in lipo battery

Packing:

A: Alcohol Pad

B: Micro-USB SuperCharger

C: Loading Tool

D: Glass Attachment

E: Atomizer

F: Base

G: Silicone Box

H: Carb Cap

I : Extra Bowl*2

How to use:

STEP 1: Fully charge device before first use. White lights pulse while charging, and turn

off automatically when complete.(1 light: 0-25%; 2 lights: 25-50%; 3 lights: 50-75% ;

4 lights: 75-100%)

STEP 2: Fill glass with water just above the air-hole. Do not fill glass while attached to base.

X- Do not allow water in lower section!

STEP 3: Align inlet hole on the front of the glass with atomizer. Carefully place the glass

into the base.

STEP 4: Hold the button for 3 seconds to turn on device (same way to turn off device).

The white lights will flash once and the ambient lights will flash sequentially red>blue>

green.

STEP 5: Single click to toggle through heat settings.

1 white light: 450ºF 2 white lights: 500ºF

3 white lights: 550ºF 4 white lights: 600ºF

Device will vibrate once while changing heat.

STEP 6: Use Loading Tool to place contents on the bottom surface of the bowl [not the side].

STEP 7: Place carb cap on top of atomizer.

STEP 8: Double click to initiate heat-

up [5 seconds avg. ], device will vibrate twice and ambient lights will be red. Single click

the button to turn off the heat-up process at anytime.

STEP 9: Ambient lights will turn green when ready. ( green lights will be on for 20

seconds, then heat up process automatically stop and ambient lights turn blue)

STEP 10: Use a cotton swab to clean the chamber after each use.

Q1. How about the MOQ?

Q2. Can I ask samples for testing before placing an order?
A. Yes we can send you some samples as your quality check, customer need to pay sample charge and shipping cost.
Q3. Can I make our logo on your vape product?
A. Yes, we accept OEM service.Please send us your logo design.
Q4. What is your terms of payment, how can we pay you?

A: Our company can accept both T/T, Paypal payment or others. If you have any other payment requirements, please leave message or contact our online salesman directly.

Factory Price E-Cigarette 1500mAh Battery Vaporizer Modhookah Wax Concentrate Shatter Budder DAB Rig Vape Electronic Vapor Cigarettes

Nanning Nuoxin Technology Co., Ltd. , https://www.nx-vapes.com